RDKS Sensoren von Schrader anstatt der OEM

Für alle als Nachtrag - dieser Beitrag hier ist super:

New TPMS sensor

Are you specifically seeking the angle valve? If not then order the part from a 2016. Because you'll get the new sensor. It's basically a smathering...

www.advrider.com

Zitat

Well, here is some knowledge about different pressure sensors / wheels got as a result of research. Corresponds to the information in this and related topics, but maybe useful to get all in one place.

KTM used 3 types of tire pressure sensors:

1. 60312033000 Tire air pressure sensor

Old and bulky one with built-in valve body. For big rim hole 11,3 mm. Was installed to: 1190 Adv / 1190 Adv R 2013-2016, 1290 SA T 2015-2017, 1290 SA R 1gen 2017-2020. Also was supplied with optional 19/17 spoke wheel set 6070990104430 for 1290 SA S 1,2 gen (2017-2020 and 2021-2024). Will fit: All Adv spoke wheels except 1290 SA R 2gen 2021-2024

2. 61412033000 TIRE PRESSURE SENSOR SMALL

For small rim hole 8,3 mm. Was installed to: 1290 SA S 1gen 2017-2020, 1290 SD R 2017-2021, 1290 SD GT 2016-2024.
Has it's specifiс mounting kit - 61412033060 VALVE 8,5MM 90° F. TPMS SMALL; 61412033050 NUT For TYRE-PRESSURE SENSOR SM

With this kit will fit all Adv/SD cast wheels. This mounting kit (valve) will NOT fit last gen sensor 61912033000 (different mounting principle)

3. 61912033000 Tire pressure sensor

Latest one. For rim hole 8,3 mm or 11,3 mm depending on mounting kit. Was installed to: 1290 SA S 2gen 2021-2024, 1290 SA R 2gen 2021-2024, 1290 SD R/Evo/RR/Brabus 2022-2023, 1390 SD R/Evo 2024-. Will fit: Any Adv/SD with correct mounting kit.

Mounting kit for any сast wheels and spoke wheels for 1290 SA R 2gen 2021-2024:
61912033060 Angle valve 8,3 mm for TPMS
0900000501500S Screw M5x15 for TPMS
(Sorry, no picture, out of stock, and too lazy to take the wheel out of the bike and disassemble))
This mounting kit will NOT fit "small" sensor 61412033000

Mounting kit for all Adv spoke wheels except 1290 SA R 2gen 2021-2024:
60309276000 Straight valve (11,3 mm)
0900000501500S Screw M5x15 for TPMS

This one also will NOT fit "small" sensor 61412033000
This kit is for big rim hole (11,3 mm) spoke wheels with rubber band inside only. Will NOT hold pressure in a cast wheel whithout additional sealant even if you drill a big hole (because of installation principle).

And we have this partnumber:
4. 60312133000 Tire air pressure sensor 433MHz cpl.

It's a set of 61912033000 sensor and 2nd mounting kit (60309276000 Straight valve (11,3 mm) and 0900000501500S Screw M5x15 for TPMS)

So, as a set will fit all Adv spoke wheels except 1290 SA R 2gen 2021-2024.
Also supplied in 890 Adv TPMS retrofit set 63512931144

and 1290 SAS 1 and 2 gen 19/17 spoke wheel set 6070990104430. Old sensor 60312033000 was replaced to 60312133000 without changing the part number of the wheel set (no info when, pucture in official factory parts finder is still with old big sensors)

Now comments:
1. All 3 sensors can be connected to any bike using "one by one" technology. Exception: 1290 SA S/R 2gen 2021-2024 (see the post above. Possible reason - these bikes are able to remember 2 sets of wheels (4 sensors), but this is nothing more than my assumptions).
2. 2 old sensors have decimal Ids, latest one - hexademical. 1290 SA S/R 2gen 2021-2024 accepts only Hex IDs. So, if you go to dealer to connect old sensors to last gen Adventure by dealer tablet - dealer will not be able to do it.
Got the info that if you do the conversion of dec ID into hex using online converter (a lot of available, google "dec to hex") - it will work. Will be able to check by myself next week, will inform.
3. If you're planning to install both front and rear sensors by yourself and then visit dealer to connect it by tablet - first take good pictures of both sensors from all sides!! Those IDs are non-obvious. On the latest sensor there is a bunch of different numbers, and the one you need looks like this: "MN58GR"

That's it. Hope will help somebody to save time/money.
BR

Alles anzeigen

Und hier mal verglichen für die Speichenfelgen mit 11,3mm Bohrung:

Falls einer eins sucht, hätte ich noch in der Garage liegen - ein RDKS mit Steuerteil für die Speichenfelgen